![]() ![]() This feature is beneficial all sunlight conditions, especially in areas with fast moving cloud cover and quickly changing solar conditions. It does not stop energy harvest to sweep the array like some other competing products. The MPPT constantly adjusts the operating points of the array to ensure it stays on the maximum power point. The MPPT 60-150 incorporates a dynamic Maximum Power Point Tracking (MPPT) algorithm designed to maximize energy harvest from the PV array. This Conext Solar Charge Controller can be installed (in single or multi-unit configurations) with Conext XW Hybrid Inverter/Charger(s) or can be used in other solar energy systems where a solar charge controller is needed. This provides flexibility for installers to use longer wiring runs without compromising efficiency. ![]() For example, the MPPT 60-150 canĬharge a 12-volt battery from a 36-volt array. The Conext XW MPPT 60-150 can be used with 12, 24, 36, 48, and 60-volt DC battery systems and is able to charge a lower nominal-voltage battery from a higher nominal-voltage array. The Conext MPPT 60-150 is Flexible and Efficient and all appropriate sections of this manual. Communicates settings and activity to other Xanbus™-enabled devices, such as the XW Hybrid Inverter/Charger, the Conext System Control Panel (SCP), Conext XW Automatic Generator Start (AGS), and other Conext Solar Charge Controllers. The Conext Battery Monitor is a meter for 24 V & 48 V batteries designed for use in off-grid power.Xanbus™-enabled network communications protocol (developed by Xantrex).Battery Temperature Sensor (BTS) included − automatically provides temperature-compensated battery charging.Over-temperature protection and power derating when output power and ambient temperature are high.Input over-voltage and under-voltage protection, output over-current protection, and backfeed (reverse current) protection (warning and fault messages appear on LCD when unit shuts down as a protective measure).Two-line, 16-character liquid crystal display (LCD) and four buttons for configuration and system monitoring.Selectable two or three-stage charging algorithms with manual equalization to maximize system performance and improve battery life.Ultra-reliable, convection-cooled design does not require a cooling fan − large, aluminum, die-cast heat-sink allows full output current up to 113☏ without thermal derating.Maximum Power Point Tracking (MPPT) delivers maximum available power from PV array to battery bank. ![]() ![]() Conext BM 00 : Basic MAIN F2 Capacity Main Battery Properties Conext SCP Battery Monitor menu Shunt mV 31.7A 75% Self Disch [3. I M Function Menu Tree MAIN MAIN F1 System Properties Configuration using the Conext System Control Panel The Conext System Control Panel (SCP) provides remote configuration and monitoring capability for the Battery Monitor and all other Xanbus-enabled devices in the network. Choose a location that is near the battery and easily accessible.Ĭonext™ Battery Monitor 865-1080-01 F G Cable Connections SYNCHRONIZE Battery shunt To auxiliary battery Twisted pair Pre-scaler board A l– (Violet wire) B I+ (Blue wire) Hold the and To inverter/charger SYSTEM BATTERY Synchronize buttons until SYNCHRONIZE flashes on the display screen. It features a local display to selectively show the voltage, current, consumed amp-hours, remaining capacity and remaining hours.ĭ1 D2 Panel Mounting Conext™ Battery Monitor 865-1080-01 Wall Mounting 60mm 3.3mm D3 DIN Rail Mounting E1 Pre-Scaler Board Mounting Install the Pre-Scaler board onto a wall with two screws (not included), as shown below. Conext™ Battery Monitor Quick Start Guide 865-1080-01 A Introduction B D Inside the Box 90mm 3.54” 82mm 3.23” The Conext Battery Monitor is a meter for 24 V & 48 V batteries designed for use in off-grid power systems as a wall/panel/DIN-rail mount device. ![]()
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |